Guidelines for Using JLR CCF Tools and VBF Editor：
JLR CCF (Control Configuration Files) tools and VBF (Vehicle Bus File) editor are software applications specifically designed for Jaguar Land Rover dealerships to configure and program vehicle control modules. These tools are only meant to be used by trained and certified technicians who have a working knowledge of vehicle systems and their components.

JLR SDD (Jaguar Land Rover Standard Diagnostic Device) Pathfinder is a software application used by Jaguar Land Rover dealerships for diagnosing and repairing vehicle systems. It allows technicians to access vehicle diagnostic information and perform various functions, such as reading and clearing fault codes, programming modules, and checking system status.

Here is a step-by-step guide to using the JLR CCF tools and VBF editor:
Step 1: Connect Diagnostic Device to Vehicle
Connect the JLR Standard Diagnostic Device to the vehicle’s OBD-II (On-Board Diagnostic) port.
Step 2: Launch JLR SDD Pathfinder
Launch the JLR SDD Pathfinder software and select the appropriate module that needs to
Step 3: Load CCF or VBF File
Load the relevant CCF or VBF file into the tool.
Step 4: Make Changes to Configuration or Programming
Using the CCF or VBF editor, make the necessary changes to the configuration or programming.
Step 5: Save Updated File to Diagnostic Device
Save the updated file to the diagnostic device.
Step 6: Upload File to Vehicle Control Module
Upload the updated file to the vehicle control module using the diagnostic device.
Step 7: Verify Changes
Verify that the changes have taken effect by performing a system test or checking for fault codes.

Conclusion
The CCF tools and VBF editor are powerful tools for configuring and programming vehicle control modules, but their use requires specialized training and certification. By following the steps outlined above, trained and certified technicians can effectively use these tools to diagnose and repair vehicle systems.

More interesting for JLR SDD software , welcome to check https://www.autonumen.com .

https://autotool.us/2023/02/28/guidelines-for-using-jlr-ccf-tools-and-vbf-editor/

This article show a guide on how to configure a Volvo Vocom Interface to WLAN wireless mode using an access point.

Procedures:
Step 1: Connect VOCOM unit/cables to the PC and a Vehicle (key off).

Step 2: Click the “Settings” button.

Step 3: In the Settings menu click the “Configuration” button. The Configuration window will open. Select WLAN.

Step 4: To identify the configured communication unit. Enter a name of your choice and select OK. (ex. Garys_Adapter or VCforJA) NOTE: If you have more than one VOCOM, each will require a separate configuration and name.

If the connected device was already configured, a confirmation message will pop up asking if you want to load the configuration or set up a new configuration.
Step 5: Make a selection here for your configuration.

Step 6: Under Connection Type choose “Access Point”. To complete the configuration, the IT person will be required to enter the data. This is the data required for the VOCOM to connect to the Wireless Router.

Step 7: Click “Save” to complete configuration setup. NOTE: In the drop down there are 3 different Security Levels to choose from.

Example: This is an example of a completed configuration for the wireless router that we used. Your configuration will need to be set according to your location’s router. NOTE: The example used a different Security Level. Your configuration will vary depending on your network environment.

Step 8: Select the newly configured VOCOM WLAN (mode) Communication Unit. Click the “Activate” button and then “OK” to close the “Settings” window.

Step 9: Unplug The USB cable and the VOCOM will be in WLAN mode. NOTE: On the Product page you can see the VOCOM is now connected with the (WLAN). When the USB cable is plugged into the PC, the VOCOM will revert to USB mode.

Done!
If you need more about the latest Auto Scanner Tools , please visit our website : https://www.autonumen.com .

https://autodiagnostic.us/2023/02/11/how-to-configure-a-vocom-to-wlan-wireless-mode/